A Westlight company - serving Henderson, NV

Door Installation Troubleshooting: Common Problems and How to Fix Them

Last updated November 17, 2026

New windows and doors improve comfort, cut energy bills and add long-term value to your home. Westlight Windows & Doors Henderson pairs proven product lines with a local vetted installing partner for lasting performance - and a price put in writing.

1

Choose your installer

The unit is half the job - the install is the other half. Background-checked local installers measure, set, seal and insulate every opening, and they know the lines we quote inside and out.

Talk to a real person →

2

Select the right products

Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.

Compare the lines →

3

Prepare your home for install

Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.

Get the install checklist →

Compare the Lines We Quote

Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.

PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
  • More impact certifications than any other line we quote
  • WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
  • 99% on-time delivery keeps your install date on the calendar
See it quoted on your openings →
CGIThe heavyweight impact line$$$$$
  • Large-missile impact ratings for the strictest wind zones
  • Architectural-grade aluminum with commercial-depth frames
  • The line we quote when protection is the whole point
See it quoted on your openings →
CWSThe value pick$$
  • Vinyl systems built to strict wind codes
  • Strong energy packages at the friendliest price point
  • The smart start for whole-home replacements on a budget
See it quoted on your openings →
ESWSlim lines, big glass$$$$
  • Narrow-sightline aluminum for modern elevations
  • Oversized openings and floor-to-ceiling glass
  • Impact-rated without the bunker look
See it quoted on your openings →
ECOThe aluminum impact workhorse$$$
  • Factory-built aluminum impact systems
  • A strong price-to-protection ratio for coastal homes
  • Proven lines with short lead times
See it quoted on your openings →

Door Installation Troubleshooting: Common Problems and How to Fix Them

A door that sticks every summer isn’t necessarily swelling. In plenty of Henderson homes, the door was installed out of square from day one, and the desert heat is simply making the math catch up. We’ve pulled enough binding slabs out of frames to know the pattern: the problem a homeowner blames on “a bad door” is often an installation error that’s been sitting quietly for years. This guide helps you tell the difference, so you don’t spend $1,800 on a replacement door when a $40 fix would have done the job.

Call (844) 797-3435

Quick Answer

Most door problems fall into three buckets: frame and rough-opening issues (the door was hung out of square or the frame has shifted), hardware issues (hinges, latch, strike plate, weatherstripping), or the door slab itself (warping, swelling, or damage). Diagnosing which one you have takes about 15 minutes with a level and a flashlight, and it’s the difference between a cheap fix and an expensive one. If the frame is the culprit, call a professional; if it’s hardware, you can often handle it yourself.

Table of Contents

The Symptom-to-Cause Chart

Start here. Match your symptom to the most likely root cause before you touch a screwdriver. This chart comes from years of service calls across Henderson, from Green Valley to Anthem, and the patterns hold up.

  • Door sticks at the top corner: Frame is racked out of square, usually from settling or a rough opening that was never plumb. Rarely a slab problem.
  • Door sticks along the latch side: Hinge screws pulling loose or the slab has swollen. Check hinge tightness first.
  • Drafts around the perimeter: Failed or missing weatherstripping, or the door isn’t sitting tight against the stop. Sometimes the frame itself is out of plumb.
  • Light gap at the bottom threshold: Threshold not set correctly, door slab cut too short, or settling that dropped the frame. Common in older Henderson subdivisions on clay-heavy soil.
  • Latch won’t catch without lifting the door: Strike plate misalignment, hinge sag, or the door has dropped on its hinges.
  • Door drags on the floor: Hinge sag, loose jamb, or the slab has warped. If it drags only in summer, the frame is moving with the heat.

In most cases, a single symptom points to one cause. When two or three show up together, that’s when we start looking hard at the frame.

Is It the Frame, the Hardware, or the Slab?

This is the test that saves homeowners the most money. Before you call anyone, spend 15 minutes narrowing down where the problem actually lives. You’ll need a 2-foot level, a flashlight, and a screwdriver.

  1. Check the frame for plumb. Hold the level against the hinge-side jamb. If the bubble is off by more than about 1/8 inch over the height of the door, the frame is out of plumb. That’s a frame problem, not a hardware problem.
  2. Check the frame for square. Measure diagonally from the top hinge corner to the bottom latch corner, then the opposite diagonal. If the two measurements differ by more than 1/4 inch, the frame is racked.
  3. Check the hinges. Open the door halfway and wiggle it up and down. Any movement means hinge screws are loose or stripped. Tighten them; if they spin, that’s a stripped hole, and it’s fixable.
  4. Check the gap around the slab. A consistent 1/8-inch gap all the way around is normal. A gap that’s tight at the top and wide at the bottom means the door has dropped or the frame has shifted.
  5. Check the slab for warp. Lay a straightedge across the door face, top to bottom. If you see daylight under the middle, the slab has warped. Warped slabs on exterior doors usually mean moisture got in, and that’s a replacement case.

Frame problems are professional territory. Hardware problems are usually a homeowner fix. Slab problems are somewhere in between, depending on whether it’s paint, warp, or physical damage.

Why Henderson Threshold Gaps Happen

Henderson sits on a lot of clay-heavy soil, and that matters more than most homeowners realize. Clay expands when it gets wet and shrinks hard when it dries out. In a Henderson summer, that cycle plays out fast. The soil under an older slab foundation moves, the foundation follows a little, and the door frame racks just enough to open a gap at the threshold.

We see this most in subdivisions built in the 1980s and 1990s, where the original thresholds were set with minimal shimming and the weatherstripping has long since hardened. A threshold gap that shows up every August and closes up in January isn’t a defective door; it’s the soil doing its thing. The fix is usually re-shimming the threshold and replacing the sweep and weatherstripping, not replacing the door.

If you’re seeing a threshold gap alongside cracks in the drywall above the door or a door that suddenly won’t latch at all, get the foundation checked before you spend money on door work. A door installation in Henderson should account for this movement from day one, with proper shimming at the sill and weatherstripping that can flex with the slab.

What You Can Fix Yourself vs. What Needs a Pro

Most of what goes wrong with a door is fixable with basic tools. Some of it isn’t, and trying to force it usually makes things worse. Here’s the honest split.

You can handle these in an afternoon:

  • Tightening or replacing loose hinge screws (a stripped hole can be fixed with a longer screw or a glued-in dowel).
  • Adjusting the strike plate up, down, or in with a file or a screwdriver.
  • Replacing weatherstripping around the frame.
  • Replacing or adjusting the door sweep at the bottom.
  • Lubricating hinges and the latch with a silicone spray (not WD-40, which attracts dust).
  • Adjusting a self-closing hinge or a door closer.

These need a professional:

  • Frame out of plumb or out of square. Re-shimming a frame without pulling the casing and trim risks cracking the wall or making the gap worse.
  • Warped door slabs on exterior doors. A warped slab won’t sit flat in any frame.
  • Rotted or water-damaged subfloor at the threshold. That’s a carpentry job, not a door job.
  • Latch and strike misalignment caused by a settling frame that keeps coming back after adjustment.
  • Any door where the fix feels like it needs a bigger hammer. That’s when a small problem becomes a $1,200 frame replacement.

If you’re not sure which side of the line you’re on, call and describe the symptom. We’ll tell you straight whether it’s a weekend project or a service call.

Drafts and Light Gaps: Tracking Down the Source

A draft around a closed door isn’t just uncomfortable. It’s a sign that the seal has failed somewhere, and in Henderson’s heat that means your cooling bill climbs every month you ignore it. Finding the source takes a flashlight and a windy afternoon.

  1. Shut the door and look for daylight. Any light showing through means air is moving too. Note exactly where: top, sides, or bottom.
  2. Run a hand around the perimeter. Feel for cool air on a hot day. Pay close attention to the hinge side and behind the weatherstripping.
  3. Check the weatherstripping. If it’s flattened, cracked, or missing in spots, it’s not sealing. This is the most common cause of drafts on doors installed more than 10 years ago.
  4. Check the door stop. The raised strip on the frame that the door closes against. If it’s loose or out of position, the door won’t seat tightly.
  5. Check the sweep at the bottom. A sweep that’s worn out or bent leaves a gap that grows in the dry season.

If the gaps are uniform around the whole door, the weatherstripping is likely the culprit. If they’re concentrated on one corner or one side, the frame is out of alignment and the sealing fix won’t hold. That’s when a professional needs to look at it, because re-sealing a misaligned door is just throwing money at a symptom.

Latch Misalignment and Sagging Doors

A door that won’t latch without a lift and a shove is one of the most common calls we get, and it’s usually one of two things: the strike plate has shifted, or the door has sagged on its hinges. Both are diagnosable in under five minutes.

Test for hinge sag: open the door to about 45 degrees and look at the gap between the top of the door and the frame. If the gap at the top hinge is wider than the gap at the top latch corner, the door has dropped. This happens because the top hinge carries more of the door’s weight, and over the years it pulls loose. Tighten the top hinge screws first. If they’re stripped, fill the holes with a small wooden dowel and wood glue, let it cure, and re-drive the screws.

Test for strike misalignment: close the door and look at the latch and strike plate from the side. The latch should slide into the strike without touching the edges. If it’s riding low or high, the strike plate needs to move. Mark the new position with a pencil, chisel out the mortise if needed, and re-drive.

If both the hinge test and the strike test come back fine but the door still won’t latch, the frame has shifted and the alignment issue is structural. That’s when a professional should look. We’ve seen Henderson homeowners chase alignment issues with new hardware for months when the real fix was re-setting the frame.

What a Warranty Callback Visit Covers

If Westlight installed your door, the 365-Day Done Right Promise means we come back and fix it if something’s not right within the guarantee period, at no charge. Knowing what to have ready when you call speeds the visit up and helps our technicians solve it on the first trip.

A callback visit covers:

  • Re-aligning hinges, strike plates, and latches on the installed door.
  • Replacing failed weatherstripping or a door sweep.
  • Re-shimming a threshold that has settled or shifted.
  • Correcting a frame that has moved out of plumb within the guarantee period.
  • Replacing hardware that has failed under normal use.

What to have ready when you call:

  • Your written guarantee (it’s handed to every customer at job completion).
  • The original written price sheet for the job.
  • A short description of the symptom and when it started (e.g. “drafts appeared last August after the heat wave”).
  • Photos of any visible gap, crack, or hardware issue (send them ahead, or have them on your phone for the tech).
  • Your preferred arrival window, so we can match it. We commit to the arrival window in writing and hold to it.

If the repair wasn’t done by us, we still come out to diagnose it. There’s no charge for the estimate, and we’ll tell you in writing what’s wrong and what it costs to fix before any work starts.

Common Mistakes to Avoid

  • Forcing a sticking door with a plane or sander. If the door is sticking because the frame is out of square, shaving the slab just opens a draft gap and doesn’t fix the cause. Diagnose first, sand last.
  • Replacing hardware to fix a frame problem. New hinges on a racked frame will fail within a season. In our experience, this is the most expensive way to learn the lesson.
  • Patching weatherstripping instead of diagnosing the gap. If the gap is uneven, new weatherstripping won’t seal it. Figure out why the door isn’t sitting flat first.
  • Ignoring a threshold gap in a Henderson summer. Clay soil moves in the dry season, and a gap that opens in August will get worse before it gets better. Fix the shimming and the sweep before the fall.
  • Using a household silicone caulk on exterior door frames. It doesn’t move with the frame the way exterior-grade sealant does, and it fails within a couple of Henderson summers. Use the right product.
  • Making an adjustment and not testing the door through a full open-and-close cycle. Plenty of “fixed” doors fail on the first cold morning. Test it three or four times, and again a week later.
  • Hiring the cheapest bid without a written price. A price that shows up for the first time at the door is not a price, it’s a guess. Every job should come with a written price sheet before the work starts.

When to Call a Professional

Call a professional if the door frame is out of plumb or out of square, if the slab is warped, if the problem keeps coming back after a homeowner fix, or if the threshold gap is accompanied by drywall cracks or a door that won’t latch at all. Those are frame-level or structural issues, and DIY fixes tend to make them worse. If the problem is hardware (hinges, latch, strike, weatherstripping), you can usually handle it yourself in an afternoon.

Westlight Windows & Doors Henderson offers free estimates in Henderson, with a written price before any work starts. Call (844) 797-3435 and a real person will pick up, day or night, ready to talk through the symptom and schedule a visit.

Frequently Asked Questions

The Bottom Line

Most door problems in Henderson aren’t broken doors. They’re installation errors, seasonal soil movement, or hardware that’s simply worn out. The three-question test (is the frame plumb, is the hardware tight, is the slab flat) tells you which one you’re dealing with in about 15 minutes, and it’s the difference between a $40 fix and an $1,800 replacement. If the frame is the issue, call a professional before you force it. If it’s hardware, you’ve probably got an afternoon project on your hands. Either way, get a written diagnosis before any work starts, and if you’re unsure, call us. We’re happy to help.

Related Guides

If you’re planning door work alongside window projects, our Westlight Windows & Doors Henderson home page covers everything we do. For broader window projects, see Window Replacement in Henderson and Window Installation in Henderson. And when it’s time to start fresh on a door, our Door Installation in Henderson page covers product lines, brands like CGI and Therma-Tru, and what the process looks like from estimate to guarantee.

Contact

Ready to get an answer instead of a guess? Westlight Windows & Doors Henderson offers free estimates in Henderson, with a written price before any work starts, background-checked technicians on every job, and the 365-Day Done Right Promise behind every install. Whether you’re in Green Valley, Anthem, or the older subdivisions where the clay soil moves most, we’ll show up in the window we gave and leave the site cleaner than we found it. Call (844) 797-3435 for a free estimate.

Written by the team at Westlight Windows & Doors Henderson.

Why Impact

Six Reasons Homeowners Choose Westlight Windows & Doors Henderson

Storm Protection

Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.

Energy Savings

Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.

Noise Reduction

Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.

Burglar Resistant

Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.

Year-Round Comfort

Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.

Property Value

A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.

Other Services

Other Westlight Windows & Doors Henderson Services

Reviews

What Neighbors Say About Westlight Windows & Doors Henderson

★★★★★

"Two bedroom windows that never opened and one that wouldn't stay up. All replaced in an afternoon. The crew was clean, hauled off the old frames, and the quote held."

CColette Rhee
★★★★★

"Front door was swollen and wouldn't latch half the year. New door and frame, done in a day. Looks great and actually seals. Written price didn't budge."

RRenee Saldana
★★★★★

"Replaced a big picture window that had a failed seal and was always foggy. Can finally see the yard again. On time, tidy, and they stood behind the install with a written guarantee."

CCarol Whitaker
★★★★★

"Our sliding patio door had come off its track years ago and we just lived with it. New one is smooth as butter. They hauled off the old one and vacuumed up before they left."

JJessica Landry
★★★★

"Windows are great and the install was solid. One of the installers was quieter and didn't explain much, but the lead walked me through everything at the end and made sure I was happy."

LLamar Jennings
★★★★★

"Got quotes from three companies. Westlight wasn't the cheapest but they were the only one who measured everything carefully and put it all in writing. Worth it. No surprises on install day."

CCraig Dillard
★★★★★

"Replaced eight drafty old windows that were basically single pane. The house is warmer already and the street noise is way down. Crew was on time both days and the price was exactly the quote."

HHarold Bemis
Need Windows & Doors help in Henderson? Licensed & insured · free written estimates
Call (844) 797-3435
Local Service Coverage

Request a Free Estimate in Henderson

Tell us what you need - Westlight Windows & Doors Henderson responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch