Last updated November 17, 2026
New windows and doors improve comfort, cut energy bills and add long-term value to your home. Westlight Windows & Doors Henderson pairs proven product lines with a local vetted installing partner for lasting performance - and a price put in writing.
Choose your installer
The unit is half the job - the install is the other half. Background-checked local installers measure, set, seal and insulate every opening, and they know the lines we quote inside and out.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
- More impact certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe value pick$$
- Vinyl systems built to strict wind codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Factory-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven lines with short lead times
Window Installation Troubleshooting: Common Problems and How to Fix Them
Window manufacturers deny roughly 70% of warranty claims on windows less than three years old, and the reason is almost always the same: the damage traces back to how the window was installed, not how it was built. That’s a fact most installers don’t mention when they hand you the warranty card. Here in Henderson, where late-afternoon sun bakes west-facing glass and summer highs push past 110°F, the gap between a well-made window and a well-installed one shows up fast. This guide maps the symptoms you’re seeing to the installation step that failed, so you can walk into a repair conversation knowing exactly what to ask and who should pay for the fix.
Quick Answer
Most problems with newly installed windows are installation defects, not manufacturing defects. A draft at the top rail usually means failed shimming; a draft at the side jamb points to missing or incomplete spray foam; fogging between the panes means the glazing seal was damaged during install; and a window that won’t lock is usually set out of plumb rather than shipped out of square. Identifying which step failed is what determines whether your warranty claim is approved or denied, and it’s what tells you whether to call the original installer or get an independent inspection first.
Table of Contents
- The Symptom-to-Cause Matrix: What Your Window Is Telling You
- Drafts That Won’t Go Away: Shimming and Foam Failures
- Fogging Between the Panes: When It’s a Product Defect and When It Isn’t
- Windows That Won’t Lock: Out of Plumb or Out of Square?
- Nail Fin Cracking in Henderson’s Thermal-Cycle Climate
- How to Document a Warranty Claim That Actually Works
- Installer Visit First, or Independent Inspection?
- When to Call a Professional
The Symptom-to-Cause Matrix: What Your Window Is Telling You
A window doesn’t fail randomly. It fails at the weakest point of the installation, and the location of the symptom tells you which step went wrong. We’ve used this diagnostic approach across hundreds of Henderson homes, from the tract houses off Warm Springs to the custom builds near Lake Las Vegas, and the pattern holds almost every time. Here’s how to read the clues before you call anyone.
- Draft at the top rail: Shimming failure. The installer either didn’t shim the top corners or shimmed only the bottom, letting the frame rack slightly under its own weight. Air moves through the resulting gap.
- Draft at the side jamb: Foam application failure. The gap between the rough opening and the frame wasn’t filled completely, or low-expansion foam was used incorrectly and shrank away from the framing.
- Fogging between the panes: Glazing seal failure during install. The insulated glass unit (IGU) was dropped, twisted, or set with too much pressure on the sash, breaking the perimeter seal.
- Window won’t lock: Frame out of plumb or the sash out of square. The lock keeper and the sash don’t meet because the window wasn’t set level.
- Water intrusion at the sill: Missing or reversed sill pan flashing. Water has nowhere to drain, so it backs up under the frame.
- Condensation on the interior glass: Usually a humidity or air-seal issue, not a glass defect. Worth checking the foam and weatherstripping before blaming the product.
Knowing which row of this matrix you’re in changes everything about the fix. A shimming problem is corrected in an afternoon. A failed IGU is a glass replacement. A flashing problem is a bigger repair that involves the surrounding wall. The point is that the symptom is a starting point, not a diagnosis, and any contractor who quotes a fix without checking should be a red flag.
Drafts That Won’t Go Away: Shimming and Foam Failures
Drafts are the most common complaint we hear about new windows, and they’re also the most likely to be blamed on the wrong thing. A new window from ViewLux or PGT is engineered to be airtight. If it’s leaking air, the failure is in the assembly, not the factory. Understanding the two separate mechanisms helps you isolate which one you’re dealing with.
Shimming is the process of setting the window level and square inside the rough opening using small wood or composite shims. It’s the step that makes or breaks a window’s long-term performance. Shims go at the sill corners, along the sill, and at the top corners, and they hold the frame true while the fasteners go in. When the top corners are skipped, the frame can deflect slightly over the first year or two of thermal cycling. Here in Henderson, where a west-facing window faces a daily swing from an overnight low in the 40s to a late-afternoon surface temp well over 150°F, that expansion and contraction is relentless. A shimmed window rides it out. An under-shimmed one opens a gap at the top rail that you can feel with a hand on a windy day.
Foam application is the second half of the air-seal. The gap between the window frame and the rough opening gets filled with low-expansion polyurethane foam, then trimmed and finished. Two things go wrong with foam, and both are common. First, the installer under-fills the gap because they’re worried about over-expansion bowing the frame. Second, they use the wrong type of foam, or they spray it when the framing is too hot, which causes the foam to skin over and pull away as it cures. The result is a gap at the side jamb that channels air straight into the wall cavity.
Here’s the simple test a homeowner can do: on a calm morning, hold a thin piece of tissue near the top rail, then near the side jamb, and watch for movement. If it flutters at the top, it’s shims. If it flutters at the sides, it’s foam. That’s a conversation you can have with a repair technician and be right about the cause before they arrive. Our own technicians have up to 17 years of experience diagnosing exactly this kind of failure, but the point of this guide is that you shouldn’t need that experience to understand what’s happening in your own home.
Fogging Between the Panes: When It’s a Product Defect and When It Isn’t
Fogging between the panes of an insulated glass unit is one of the most misdiagnosed window problems, and it’s the one where manufacturers push back hardest on warranty claims. The reason is simple: a fogged IGU can come from the factory with a defective seal, or it can be perfectly manufactured and destroyed during installation. The manufacturer knows the difference, and their inspectors look for specific signs before approving a claim.
The IGU is the sealed sandwich of glass, spacer, and desiccant that makes up your window’s energy performance. The perimeter seal is a thin bead of butyl or silicone that keeps the argon or air inside and moisture out. When that seal is compromised, moisture gets in, the desiccant beads saturate, and fogging begins. So far, so straightforward. But what compromises the seal?
- Twisting during install. If an installer sets the IGU into the sash and it doesn’t seat flat, the frame can flex and pull the seal loose over the first thermal cycles.
- Pressure on the sash. Setting a window frame out of plumb puts constant stress on the sash, which transfers to the IGU perimeter.
- Improper glazing compound or gasket placement. Setting blocks and gaskets placed in the wrong position can pinch the seal.
- Factory defect. Rare, but it happens. A bad seam at the spacer joint shows up fast, usually within the first heating season.
How do you tell the difference? In our experience, factory defects show up early and identically across the same batch of windows. If one window on a job is fogging and the other seven are fine, the problem is almost certainly the install. If all eight are fogging within a few months of each other and they were all made the same week, the batch has a manufacturing issue. If you’ve had Window Installation in Henderson done recently and you’re seeing fogging in a single window, document it now. A fogged IGU under warranty gets replaced. A fogged IGU that gets blamed on installation defect after the manufacturer inspects it is a repair you pay for yourself.
Windows That Won’t Lock: Out of Plumb or Out of Square?
A window that won’t lock properly is one of the most obvious signs of an installation problem, but homeowners often blame the lock hardware first. In almost every case we’ve seen, the lock is fine and the frame is not. The lock keeper on the jamb and the lock mechanism on the sash have to meet at a precise alignment. If they’re off by even a few millimeters, the window won’t catch, or it will catch with visible pressure and a gap.
The key distinction is out of plumb versus out of square, and it’s the difference between an installation defect and a shipping defect. Out of plumb means the window frame is not perfectly vertical in the rough opening. The installer didn’t level the unit before fastening it down, so it leans slightly. This is 100% an installation defect, it’s the installer’s responsibility to correct, and it usually shows up as a window that won’t lock anywhere along the jambs, top and bottom, or that locks at the top but not the bottom.
Out of square means the window left the factory with slightly unequal diagonal measurements across the frame, so the sash was never going to fit the frame properly no matter how carefully it was installed. This is a manufacturing defect, and it’s the manufacturer’s responsibility. It shows up as a sash that fits one corner of the frame snugly and leaves a visible gap at the opposite corner, regardless of how the window was set.
How can you tell which you have? The test is simple and you can do it yourself before you call anyone:
- Look at the gap around the sash where it meets the frame. If the gap is uneven side to side (wider on the left than the right, for example) but even top to bottom, the frame is racked and probably out of plumb.
- If the gap is uneven diagonally (wide at top-left and bottom-right, tight at the other two corners), the sash itself is probably out of square.
- Measure the diagonal across the frame’s outer corners both ways. If the two diagonal measurements are more than about 1/8 inch different, the window was manufactured or shipped out of square. If they’re equal but the frame isn’t vertical against the wall, it’s an install problem.
This distinction is everything, because it determines who pays. An out-of-plumb window is a free call-back from the installer, under warranty. An out-of-square window is a factory claim, and those go through slower. Neither involves paying for a new window yourself, but knowing which claim to file saves you months of being passed around.
Nail Fin Cracking in Henderson’s Thermal-Cycle Climate
Nail fin cracking is a specific problem in Henderson that most window guides written for other parts of the country skip over, and it’s the clearest example of how local climate exposes installation defects that would stay invisible in a milder place. The nail fin is the flange around the perimeter of the window that the installer fastens through. It’s how the window attaches to the rough opening, and it’s what makes the whole unit rigid.
In Henderson, the daily thermal cycle is extreme. A west-facing window frame can sit at 90°F at breakfast and 150°F or more by late afternoon in July, and then drop 40 degrees overnight. The nail fin expands and contracts with that swing. If the installer over-drove the fasteners through the fin, or if they fastened the fin rigidly at the corners without the small tolerance gap the manufacturer specifies, the expansion has nowhere to go. It concentrates at the fastener holes and the corners, and the vinyl or aluminum fin cracks over time.
Here’s what nail fin cracking looks like:
- Hairline cracks radiating from the fastener holes on the fin, visible from the exterior.
- Corners of the fin that have split away from the frame, leaving a gap you can see daylight through.
- Caulk or flashing pulling away from the fin because the fin has moved independently of the wall.
- Cracks that appear in the first two summers, then stop growing, or cracks that keep growing every winter.
Nail fin cracking is an installation defect, not a material defect, even though it looks like the vinyl itself failed. The vinyl performed exactly as it was designed to under normal expansion. What failed was the installation, and that’s what makes the difference between a warranty claim that gets approved and one that gets denied. If you’ve had new windows installed in a Henderson home anywhere from Anthem to Green Valley and you’re seeing cracks radiating out from the screw heads, the right person to call is the installer, and the right time to call is before a monsoon season drives water into the crack. The framed flare around a bad nail fin doesn’t keep water out for long.
How to Document a Warranty Claim That Actually Works
A warranty claim on a window succeeds or fails on documentation. The manufacturer’s inspector, the installer’s warranty department, and the homeowner are all trying to figure out the same thing: did this window fail because of how it was made or how it was installed? Your job is to make it obvious. Most denied claims are denied because the homeowner can’t prove what they described, not because the claim was invalid.
Start documenting the moment you notice a problem. Here’s the exact process we recommend, and it’s the same one that turns a 50/50 claim into a certainty:
- Photograph the symptom, then the context, then the measurement. A close-up of the draft at the top rail, then a wide shot of the whole window from inside, then a photo of a tape measure against the uneven gap. Three photos per symptom, minimum. Take them in daylight.
- Measure and write down the numbers. The gap width at each corner of the sash in millimeters. The diagonal measurements across the frame both ways. The exact dimensions of the rough opening. Write these in a notebook with the date and time, not on your phone only. Date each entry.
- Note the conditions. What’s the weather doing? Is the draft worse on a windy day, at a particular time of day, when the AC is running, or after a rainstorm? The installer’s tech will ask; having a written record is what makes the answer credible.
- List every affected window. Tag each with the room it’s in and the window’s position, so you’re not re-identifying them by memory later. “The one by the kitchen sink” is not a workable identifier on a warranty form.
- Save the original contract, the written price, and the warranty card. If you got a written price before work started, keep it. That document is your evidence of what was promised and when.
- Email the claim with photos attached and request an acknowledgement. Send the claim by email and keep the reply. A phone call is easy to deny later; an email with photos is not.
Our own practice here at Westlight is that every customer gets the written price and a written guarantee at job completion, which means when a call-back is needed, there’s no debate about what was promised. That’s not a standard every installer meets, which is exactly why it matters that you keep your own copy. A warranty is only as good as the paper trail behind it.
Installer Visit First, or Independent Inspection?
When you’ve got a documented problem, the natural next move is to call the original installer and schedule a troubleshooting visit. That’s the right move in most cases, but not all of them. Knowing which situation you’re in saves you weeks and, occasionally, a small fortune.
Start with the installer when: the problem is clearly an installation defect (draft at the side jamb, window out of plumb, nail fin cracking), your installer is responsive and you have a written guarantee from them, and the window is still under their workmanship warranty. A troubleshooting visit from the original installer is fast, it’s usually free, and if the fix is simple (re-shimming a corner, re-foaming a jamb), they can do it in an hour.
Get an independent inspection first when: your installer has gone quiet or is arguing that the problem is a product defect, the fix involves structural elements (flashing, wall finish), the repair cost is significant, or you’re within a claim window on a warranty that requires a third-party report. An independent inspector’s report carries weight with both the installer and the manufacturer, and it protects you if the claim ends up in a dispute.
One practical note: if your installer is a contractor you’ve lost confidence in, don’t let them back in the house without a documented reason to be there. That sounds cold, but a bad install is a business problem, and a site visit without a written purpose gives them a chance to reframe the problem on their terms. If you’re unsure which of these situations you’re in, that’s the moment to get a second opinion. We offer free estimates for Window Replacement in Henderson because a lot of homeowners end up deciding it’s faster to start fresh than to chase a warranty that’s gone nowhere. Either outcome is fine, but you should know which one you’re facing before you sign anything.
Common Mistakes to Avoid
- Blaming the glass before checking the frame. Fogging gets all the attention, but in our experience most “bad glass” calls turn out to be bad seals caused by the frame being set wrong. Look at the frame first.
- Caulking over a draft instead of fixing it. A bead of caulk over a top-rail draft hides the symptom for one season and traps moisture behind it. The shimming problem underneath hasn’t gone anywhere.
- Filing a warranty claim before documenting conditions. The manufacturer’s inspector will ask for measurements and photos. If you don’t have them, the claim stalls and the burden of proof shifts to you. Start the photo record the day you notice the problem.
- Ignoring nail fin cracks because they look cosmetic. In Henderson’s monsoon season, a cracked fin is a water intrusion path, not a cosmetic flaw. Water behind the wall finish is expensive to fix.
- Accepting a verbal “we’ll come look” instead of a written appointment window. Contractors who won’t commit to an arrival time in writing are the same ones who no-show. A committed window is the lowest bar there is, and it tells you a lot.
- Assuming “same day” means a real install schedule. Window installation is not an emergency repair. If a contractor promises your full installation will be done same-day, ask what they’re skipping, because something is getting rushed.
- Forgetting the warranty card and the written price. The two documents that determine who pays for a repair are the original written price and the warranty that came with it. Keep them together, in a folder, where you can find them in a year.
When to Call a Professional
Some window problems are a homeowner’s to diagnose. Others need a technician on sight. Call a professional if the window has visible water intrusion at the interior wall or floor, if a window has cracked or broken glass (stop using that window and call, don’t try to cover it yourself), if the frame is visibly separating from the wall, if a window has come out of its track and a child or pet could be near it, or if you’ve gone through the documentation process above and you’re still not sure what you’re looking at. Safety first on anything involving glass or an unsecured opening. For everything else, the free estimate is the path forward. Westlight Windows & Doors Henderson offers free estimates in Henderson; call (844) 797-3435 to schedule yours. Our lines are answered by a live person 24 hours a day, so you don’t have to guess when to call. You can also see the full range of window installation services and door installation services we offer for the broader project picture.
Frequently Asked Questions
Drafts in new windows almost always come from an incomplete air seal at the frame, not from the window itself. A draft at the top rail is typically failed shimming; a draft at the side jamb is incomplete or incorrectly applied foam. Both are installation issues and should be corrected by the installer under their workmanship warranty. Call (844) 797-3435 for a free estimate if you need a second opinion on a draft that won’t go away.
It depends on the pattern. If one window fogged and the rest of the batch is fine, the installation was likely the cause and the manufacturer will probably deny the claim. If multiple windows from the same batch are fogging at the same time, that points to a manufacturing seal defect and the claim has a better chance. Document either case with photos and measurements before you file.
A window that won’t lock is almost always out of plumb (an installation defect) rather than out of square (a shipping or manufacturing defect). Check the gap around the sash: uneven side to side means the frame is racked, uneven diagonally means the sash itself is off. An out-of-plumb window is the installer’s responsibility to fix. Call (844) 797-3435 to schedule a free estimate if you want the problem diagnosed by a technician.
Check three things. First, the windows should be level and square with even gaps at every corner of the sash. Second, the exterior nail fin should be free of radiating cracks at the fastener heads after the first summer, since Henderson’s thermal cycle exposes a poor fastening job quickly. Third, you should have a written price and a written workmanship guarantee in hand at job completion. If all three are there, the install was done right.
No, and we’d recommend against trying. An out-of-plumb window has to be re-shimmed, which means pulling fasteners out of the framing and resetting the unit, and that work involves working around the perimeter flashing and the surrounding wall. This is installer work and it’s covered under their warranty. Leave it to a professional; the risk of a worse problem is real.
Permit requirements for window replacement depend on the scope of the work and the current local code, and any contractor you’re considering should be able to tell you in writing whether a permit is required for your specific project. Ask before work starts and get the answer on paper. A contractor who shrugs at the question is a contractor to skip. Call (844) 797-3435 to discuss your project and the permit situation for your Henderson home.
The Bottom Line
New windows that develop problems within the first two years are usually well-made windows that were installed wrong. A draft at the top rail means shims failed; a draft at the side jamb means foam failed; fogging means the glazing seal was damaged during install; a window that won’t lock is probably out of plumb; and nail fin cracks in a Henderson home are the clearest sign that the fasteners were over-driven for the local thermal cycle. Document every symptom with photos and measurements, and know which claim you’re filing before you call anyone. If you need a professional to look at the problem and give you a straight answer, Westlight Windows & Doors Henderson can help. Call (844) 797-3435 for a free estimate, or start from the Westlight Windows & Doors Henderson home page to see how we work.
Written by the team at Westlight Windows & Doors Henderson.
Six Reasons Homeowners Choose Westlight Windows & Doors Henderson
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.