Last updated November 17, 2026
New windows and doors improve comfort, cut energy bills and add long-term value to your home. Westlight Windows & Doors Henderson pairs proven product lines with a local vetted installing partner for lasting performance - and a price put in writing.
Choose your installer
The unit is half the job - the install is the other half. Background-checked local installers measure, set, seal and insulate every opening, and they know the lines we quote inside and out.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line homeowners arrive naming - the most impact certifications in the industry$$$
- More impact certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe value pick$$
- Vinyl systems built to strict wind codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Factory-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven lines with short lead times
Window Installation Maintenance Schedule: What to Do and When
Most window warranties require documented maintenance to stay valid, but fewer than one in ten homeowners know what “documented maintenance” actually means. An installer who doesn’t explain it is quietly setting up a denial. New windows aren’t finished when the last screw turns – they spend their first 24 months settling, and the checks you make in that window are the ones that catch installation errors while the manufacturer still covers them. This guide lays out a real calendar for Henderson homeowners: what to do at 30 days, 90 days, 12 months, and every year after, which products to use, and what to write down so a warranty claim never bounces back at you.
Quick Answer
Newly installed windows need a check at 30 days (seals, hardware, drainage), 90 days (settling and caulk joints), and 12 months (full operating and gasket inspection). After year one, inspect every six months, re-caulk exterior joints as needed, and lubricate hardware annually. Keep a simple written log of every check and repair – most manufacturer warranties require it. In Henderson, caliche dust makes hardware maintenance a bigger job here than in most cities.
Table of Contents
- The First 24 Months: Your Settling Period
- The 30-Day and 90-Day Checks
- The 12-Month Inspection That Protects Your Warranty
- Sealants and Caulk: Doing It Without Voiding the Warranty
- Henderson Dust and Your Lock Mechanisms
- By Window Type: Casement, Single-Hung, Sliding, Awning
- What to Record (and How to Format It)
- Years Three Through Ten: The Long Schedule
The First 24 Months: Your Settling Period
Here’s the part generic guides skip. A newly installed window is not the same object as a five-year-old window. The rough opening was just cut, shimmed, insulated, and sealed. Wood framing moves as it adjusts to a new load. Foam and sealant cure and shrink slightly. In Henderson’s dry desert air, that settling happens faster and more noticeably than in a humid climate, because the framing is losing and regaining moisture with every seasonal swing.
All of this means the first two years are when installation errors reveal themselves – and it’s also the window when a good installer’s warranty is still covering the fix at no charge. Miss those checks and a small gap at a sill can turn into a water stain on drywall by year four, well past the point where anyone will call it an installation fault.
A few things we look for specifically in that settling period, and that you can watch for yourself:
- Daylight or draft at the frame. Any visible gap between window and wall, or air you can feel on a windy day, points to a seal that let go.
- Sticking or dragging. A sash that operated smoothly at install and now catches is telling you the frame has shifted. In Henderson, this often shows up on south- and west-facing windows first because of thermal movement.
- Water tracking inside the sill. Wipe the sill after a rain. Persistent moisture means the exterior seal or weep system is failing.
- Hardware that loosens. Screws backing out a quarter turn over six months is normal. Screws that keep loosening after you tighten them is not.
Document each of these with a date and a photo. That record is gold if you ever need service. If you’re not sure whether what you’re seeing is settling or a real defect, a look from the installing company costs nothing and settles the question. You can read more about how installation is handled on our Window Installation in Henderson page.
The 30-Day and 90-Day Checks
Mark these two dates on your calendar the day the crew leaves. They’re the highest-value checks you’ll ever make on the windows.
The 30-day check
- Operate every window fully open and fully closed three times. Note any that catch, squeak, or don’t latch cleanly.
- Run a hand along the interior perimeter of each frame. Feel for cool air on a windy morning – that’s your draft test.
- Look at every exterior caulk joint at eye level. Hairline cracks at 30 days are common as the sealant cures; you want to catch them early.
- Check that weep holes (the small slots at the bottom of the outside frame) are open and clear. Painters and stucco crews sometimes plug them.
- Wipe down hardware and look for loose screws on handles, cranks, and locks.
The 90-day check
- Repeat the draft and daylight test. Settling has progressed by now, and any frame movement will show.
- Inspect interior trim joints for cracks. Small cracks are cosmetic and easily filled; wide separation means movement worth documenting.
- Re-test every lock and latch. A lock that suddenly needs force is a sign of alignment shift.
- Look for water staining in the drywall or stucco around each opening after any rain. Henderson gets fewer storms than the coast, but a monsoon downpour finds every gap.
If anything on this list looks wrong, call the installer. It’s covered, and it’s covered easily at 90 days. It stops being easy at three years.
The 12-Month Inspection That Protects Your Warranty
At the one-year mark, your windows have gone through a full Henderson seasonal cycle – the cool winter, the dry spring, the summer heat, and the late-summer monsoon push. That’s why the 12-month inspection matters more than any other single check: it’s your one-commit-to-full-system look while the installation warranty is still fresh.
Do a complete pass on every opening:
- Glass and glazing: look for fogging between panes, which signals a failed seal unit. Modern insulated glass from lines like CGI and ECO Window Systems rarely fails this early, but when it does, it’s a warranty item and you want it logged at year one.
- Gaskets and weatherstripping: compress each one with a fingernail. Stiff, cracked, or flattened stripping needs replacing. Desert UV is hard on rubber, so this becomes an annual item going forward.
- Exterior sealant: a full walk-around with a flashlight. Re-seal any joint showing a crack, gap, or pull-away, following the product guidance in the next section.
- Operating hardware: cranks, hinges, rollers, and locks all get cleaned and lubricated.
- Drainage: confirm weep holes are open and that water on the exterior sill drains away from the wall.
Record the date, what you checked, and anything you fixed. That single page becomes the foundation of your maintenance documentation. If a window was installed as part of a larger Window Replacement in Henderson project, pull out the warranty paperwork before this inspection so you know exactly what you’re required to do and what the manufacturer expects you to keep.
Sealants and Caulk: Doing It Without Voiding the Warranty
This is where homeowners accidentally undo a perfectly good installation warranty. You grab whatever caulk is in the garage, seal a joint the installer wanted left alone, and now the drainage system is blocked – and the manufacturer says the leak is your fault.
Three rules keep you out of trouble:
- Match the product to the joint. Exterior perimeter joints call for a high-quality exterior sealant rated for masonry and metal, typically a polyurethane or high-grade siliconized product. Interior trim joints take a paintable acrylic caulk. Don’t substitute one for the other.
- Never seal the weep holes. Those slots at the bottom of the outside frame exist to let water out. If you caulk over them, water sits behind the frame and heads inside. This is one of the most common warranty-voiding mistakes we see.
- Don’t caulk over wet or dirty surfaces. In Henderson, caliche dust drifts onto every exterior frame, and caulk won’t bond to it. Clean and dry the joint before you apply anything.
If the manufacturer specified a particular sealant in the installation paperwork, use that one. If you’re not sure, call and ask before you squeeze the tube. A two-minute question beats a denied claim – and homeowners who chose Door Installation in Henderson alongside their windows have the same rule at every door perimeter joint.
Henderson Dust and Your Lock Mechanisms
If you moved to Henderson from a wetter climate, the hardware schedule here will feel aggressive. It needs to be. Fine caliche dust – the powdery mineral soil that covers so much of the valley – gets airborne on windy days and settles into every lock, crank, and track on the windward side of your house. Over a season, that grit grinds at metal-to-metal contact points, and a lock that felt smooth in spring can operate roughly by fall.
The fix is simple, but the product matters. Most standard lubricants are too light and will evaporate within weeks, and oil-based products actually attract more dust – the opposite of what you want. What works:
- Dry film or silicone-based lubricant for lock cylinders and cranks. It leaves a thin, relatively dry surface that doesn’t grab dust the way oil does.
- Graphite powder inside key cylinders, applied sparingly. It stays put and won’t attract grit.
- A soft brush or canned air to clear the lock mechanism and window track first, before any lubricant goes on. Lubricating over top of dust just makes paste.
Clean and treat hardware in the spring, before the windy season peaks, and again in the fall. Homes on the west edge of Henderson, closer to the open desert west of the valley, tend to need it most.
By Window Type: Casement, Single-Hung, Sliding, Awning
The calendar stays the same, but what you actually inspect changes by window type. Since most Henderson installation projects mix several styles – casement windows in a bedroom, slider in a patio wall, awning windows over a kitchen sink – it helps to know which parts live on which window.
Casement windows (crank-operated, hinge on one side) need the most attention to their crank mechanism and hinge hardware. The crank gearing collects dust and needs a light annual clean and silicone lube. Check the gasket around the sash perimeter, since casements seal by compression and a flattened gasket lets air through. Open them fully every few months rather than a quarter turn – hinges that never fully extend still seize.
Single-hung windows (top sash fixed, bottom sash slides) are the simplest to maintain. The key items are the balance springs or cords inside the frame and the sash lock. If the bottom sash drops on its own or the lock won’t line up, the balance mechanism needs a look. Don’t take the sash out yourself – that’s a two-person job with a spring under tension.
Sliding windows live or die by their tracks. Henderson dust settles into the bottom track and rollers grind if it isn’t cleared. Vacuum the track and clean the rollers every six months, and use a dry silicone spray on the track, not oil. A slider that suddenly takes two hands means the rollers or track need attention.
Awning windows (hinged at the top, opening outward) have their own hardware – a hinge bar and operator arm – and the same gasket-compression rule as casements. Because they sit higher on the wall, they’re easy to forget. Add them to your inspection list by name, and if the operator arm binds, stop and call rather than force it – the linkage is under load and can snap.
Products from lines like CWS and ES Windows come in multiple styles, so your installation paperwork tells you exactly which components you have. Keep that sheet.
What to Record (and How to Format It)
“Documented maintenance” is exactly what it sounds like: a written record that you did the checks the manufacturer required. It doesn’t need to be fancy. It needs to be consistent, dated, and kept somewhere you can find it in two years.
A simple log format that satisfies most manufacturer warranty requirements:
- Date of each inspection or repair.
- Window location – use a short label per opening, like “front bedroom east” or “kitchen sink awning,” so every entry points to a specific unit.
- What you did – a short note: “cleaned track and rollers,” “re-caulked exterior sill joint,” “lubricated lock cylinder.”
- What you saw – any issue noticed, and whether it was fixed or referred to the installer.
- Receipts and product labels for any caulk, lubricant, or replacement part you used. A photo of the product label works.
- Photos of anything that looked wrong before you fixed it, and after.
Keep the log with your warranty paperwork – one folder, paper or digital, doesn’t matter. When anyone asks you to demonstrate that maintenance was done, you hand them the log. If you ever sell the home, that log is a genuine selling point to a buyer who wants to know the windows were looked after.
Years Three Through Ten: The Long Schedule
After the initial settling period, the schedule settles too. Here’s how the calendar looks from year three on, and how it differs from what most generic guides describe. The big shift is that the risks change: with settling done, the dominant threats become UV damage to gaskets and weatherstripping, sealant age, and the glass itself.
- Every six months: clean tracks and hardware, clear weep holes, run a full open/close pass on every window.
- Annually: lubricate all hardware with silicone or dry film; inspect gaskets and weatherstripping for stiffness or cracking and replace worn pieces; inspect and touch up exterior sealant.
- Every three to five years: a closer look at the glass seal units. A failed seal shows as fogging between panes, and with a well-performing line it can still happen after year five – if it does, call the manufacturer’s warranty line before assuming it’s on you.
- After year ten: have the windows inspected professionally every few years. Most homeowner-installed windows last 20 years or more, but desert UV accelerates wear on exterior parts. A professional look catches a failing gasket or sealant joint before it becomes a wall problem.
The difference between a Henderson window that lasts 20 years and one that lasts 12 usually isn’t the glass. It’s whether someone cleaned the dust out of the tracks and re-sealed the joints on schedule. That’s the whole job, repeated.
Common Mistakes to Avoid
- Caulking over the weep holes at the bottom of the exterior frame. Those slots are the window’s drainage system, and sealing them traps water behind the frame. It’s the fastest way to void an installation warranty.
- Using oil-based lubricant on locks and tracks. In Henderson’s dusty air, oil grabs caliche grit and turns into grinding paste. Use silicone or dry film instead.
- Skipping the 30-day check because everything looked fine at installation. Settling and curing happen in the first weeks, and that’s exactly when a fix is free.
- Assuming a foggy pane is your problem. Fogging between panes is a failed seal unit and usually a warranty item – log it at the 12-month inspection, don’t ignore it until year six.
- Throwing away the installation paperwork and warranty card. You can’t make a claim if you can’t name the product or the terms. File them with your log the day you receive them.
- Forcing a sticking casement crank or awning operator rather than stopping. The linkage is under load and will snap, turning a simple adjustment into a replacement part.
- Trying to fix water intrusion at the frame with interior caulk. Water that’s getting in at the exterior won’t stop because you plugged the inside. It’ll just find a new exit.
When to Call a Professional
Most of this calendar is homeowner work. A few situations aren’t, and calling early saves the wall behind the window. Call us when you see water tracking inside a sill or staining around a frame, when a window won’t open or latch at all, when you spot fogging between panes, or when a casement or awning operator binds under load. Anything involving a second-story exterior joint or a window above a hard surface isn’t a ladder job for a homeowner. And if you’re not sure whether what you’re looking at is normal settling or an installation fault, a professional look costs nothing to schedule and settles the question – especially on windows installed within the last two years, when an installer’s warranty may still cover the fix.
Westlight Windows & Doors Henderson offers free estimates in Henderson – call (844) 797-3435. We install from eight manufacturer lines, and every job is governed by the Kingswell Guarantee: a written price before any work starts, a committed arrival window, a clean job site, and a written guarantee on the completed work. If a repair fails, we come back and fix it at no charge.
Frequently Asked Questions
Check them at 30 days, 90 days, and 12 months after installation, then twice a year after that. The early checks catch settling issues while warranty coverage is strongest. Open, close, and visually inspect every window at least every six months – that’s the minimum to keep most manufacturer warranties valid and to catch problems before they spread.
Yes – most manufacturer warranties require documented maintenance to remain valid. The paperwork typically specifies periodic inspection and care, and the manufacturer can deny a claim if you can’t show it was done. Keep a dated log of your checks and repairs, plus receipts for any products used. If you’re unsure what your warranty requires, call (844) 797-3435 and we’ll help you find the terms on your paperwork.
Fine caliche dust is airborne on windy days and settles into locks, cranks, and tracks, where it acts like grinding compound. That’s why Henderson windows need hardware cleaned and lubricated more often than in wetter climates. Use a dry film or silicone-based lubricant, and clear the dust out first – oil-based products make the problem worse by attracting more grit. Cleaning in spring and fall keeps the hardware smooth.
A routine inspection or minor hardware service typically lands in the $100-$250 range depending on how many windows are checked. Work that turns out to be covered by the installation or manufacturer warranty is corrected at no charge when the issue falls under the guarantee period. Call (844) 797-3435 for a free estimate – you’ll get a written price before anything starts.
New windows spend their first 24 months settling, so the early checks focus on frame movement, draft at the perimeter, hardware alignment, and caulk curing. Older windows need the focus on aging gaskets, worn hardware, glass seal units, and re-sealing exterior joints. Following the schedule in the right order matters: fix settling issues in year one, then shift to wear-and-tear checks after year three.
Usually yes, if you follow the product guidance in the installation paperwork and never seal the weep holes. Use an exterior sealant rated for masonry and metal on perimeter joints, keep interior trim work to paintable acrylic, and clean the surface first. If the manufacturer specified a product, use that one. Call (844) 797-3435 before applying anything if you’re unsure – a two-minute question prevents a denied claim.
The Bottom Line
Newly installed windows need a different schedule than aging ones. The first 24 months are your settling period – check at 30 days, 90 days, and 12 months, and catch installation errors while the warranty is fresh, before they become wall problems. After that, the job shifts to twice-yearly hardware cleaning, annual lubricant, periodic gasket and sealant checks, and a close look at the glass seal units every three to five years. Henderson’s caliche dust makes hardware maintenance a bigger deal here than in most cities, so use silicone or dry film lubricant and never oil. Keep a dated log. That page is what lets a warranty claim get paid instead of denied. And if something looks wrong, call before you force it – a professional look costs nothing to schedule and often catches a covered issue while it’s still covered.
Written by the team at Westlight Windows & Doors Henderson.
Six Reasons Homeowners Choose Westlight Windows & Doors Henderson
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.